Axpert VM III Twin 6000 W 48 V off-grid inverter with 450 V MPPT and second TWIN output, PF 1.0
Code: OST_570024Product detailed description
High-voltage MPPT and a second output in one unit
Axpert VM III Twin 48 V 6000 W PF1 is derived from the VM III series. It is a hybrid off-grid inverter with a built-in battery charger that can be backed up by the public grid or a good-quality generator. The MPPT solar controller works with panel voltages of 60–450 V (max. 500 V open circuit) and PV arrays up to 6000 Wp; at least 100 V Vmpp is recommended. Thanks to a power factor of 1.0 the maximum output is 6000 W.
The new feature is the TWIN function – a second configurable 230 V AC output. You can switch it according to the battery state of charge (SOC) or voltage and thus send surplus electricity to a water heater, for example. The inverter is also one of the first models to manage batteries by SOC, i.e. by percentage.
It communicates directly with Pylontech and Pytes batteries (48 V) and, if needed, can also run completely without a battery. In battery-free mode, however, zero export to the grid cannot be guaranteed. With batteries you use more solar energy and your appliances stay powered even during a grid outage. Configuration is done on the display or from a mobile phone or computer.
Functions and protection
- pure sine wave output; in battery mode the frequency and phase remain identical to the grid input, so switching is seamless for appliances
- grid charging current adjustable in steps of 2, 10, 20, 30, 40 and 50 A, AC or solar input priority selectable on the LCD
- protection against overload (switches to bypass at 110–200 %), short circuit (the inverter shuts down) and battery discharge (switches to bypass)
- automatic restart after overload or overheating clears, cold start for gradual load start-up
- smart charger for longer battery life
- potential-free relay (dry contact) signalling discharged or fully charged batteries
- standby consumption 2 W, 50 W in battery mode
Connection and compatibility
The inverter is intended only for TN-S or TN-C-S networks. In two-wire TN-C networks (phase + PEN) it may be damaged or malfunction. Connect the high voltage of the PV panels only when the inverter is switched off, otherwise the product may be damaged. The PV current may be at most 27 A.
Pylontech batteries are connected with a UTP cable to the RS485 port: for type B with pin assignment 1-3, 3-1, 2-5, 5-2, for type C 3-8 / 5-7. Set the speed to 9600 bps with the first DIP switch on the battery.
This is regulated technical equipment: installation and commissioning must be carried out by a qualified person and the equipment is subject to an initial inspection.
Frequently asked questions
Can the VM III Twin be connected in parallel or in three phases?
No, this inverter does not support parallel or three-phase systems.
What is the TWIN output for?
It is a second 230 V AC output that switches on according to the battery SOC or voltage – typically for heating water in a water heater from surplus energy.
Can the inverter work without a battery?
Yes, but zero export to the grid is then not guaranteed. We therefore recommend using batteries.
Technical specifications
| Brand | Axpert |
| Manufacturer | Voltronic Power |
| Order number | 96-346120-01G |
| Type | off-grid inverter with grid backup and MPPT |
| Rated power | 6000 VA / 6000 W (PF 1.0) |
| Peak power | 12000 VA |
| Output voltage | 230 V AC, pure sine wave |
| Transfer time | 10 ms (computers) / 20 ms (appliances) |
| Max. efficiency | 93 % |
| Battery voltage | 48 V DC |
| Float voltage | 54 V DC |
| Max. charge current | 120 A (100 A from grid) |
| Max. PV array power | 6000 W |
| Max. PV open-circuit voltage | 500 V DC |
| MPPT range | 60–450 V |
| Max. PV input current | 27 A |
| Second TWIN output | yes |
| Parallel / 3-phase connection | no |
| Dimensions (H × W × D) | 435 × 300 × 115 mm |
| Weight | 10.5 kg |
Additional parameters
| Category: | Photovoltaics |
|---|---|
| Warranty: | 2 years |
| Weight: | 10.5 kg |
| Brand: | Axpert |
| Manufacturer: | Voltronic Power |
| Order number: | 96-346120-01G |
| Type: | off-grid inverter with grid backup and MPPT |
| Rated power: | 6000 VA / 6000 W (PF 1.0) |
| Peak power: | 12000 VA |
| Output voltage: | 230 V AC, pure sine wave |
| Transfer time: | 10 ms (computers) / 20 ms (appliances) |
| Max. efficiency: | 93 % |
| Battery voltage: | 48 V DC |
| Float voltage: | 54 V DC |
| Max. charge current: | 120 A (100 A from grid) |
| Max. PV array power: | 6000 W |
| Max. PV open-circuit voltage: | 500 V DC |
| MPPT range: | 60–450 V |
| Max. PV input current: | 27 A |
| Second TWIN output: | yes |
| Parallel / 3-phase connection: | no |
| Dimensions (H × W × D): | 435 × 300 × 115 mm |
| Weight: | 10.5 kg |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
