Flanged solenoid valve for heating gases IVAR.M16-RMP – DN 100, PN 6, NC
Code: CX10C0000008Product detailed description
The flanged solenoid valve for heating gases IVAR.M16-RMP DN 100, PN 6, NC (CX10C0000008) shuts off the gas supply on a signal from a leak detector or a safety thermostat. It is normally closed: open only while the coil is powered, and without voltage, even in a power cut, it stops the gas.
Function
After closing, the valve is reopened by hand (reset), which allows the cause of the leak to be checked; this is also needed after a power cut. According to the data sheet it may be reopened only under voltage and with no alarm signal from the detector. The valve meets STN EN 161 and STN EN 13611.
Technical data
- flange connection DN 100 to ISO 7005 / EN 1092-1, PN 6
- non-aggressive dry gases of families I, II and III (natural gas, carbon monoxide, LPG)
- ambient temperature -20 °C to +60 °C
- supply 230 V, 50 – 60 Hz (tolerance -15 % to +10 %), protection IP65, cable gland M 20 x 1.5
- closing time under 1 s, filter element 50 µm
- body of die-cast aluminium, NBR and Viton seals
- DN 100 dimensions: A 350, B 363, C 260, D 105, E 258 mm
Gas equipment may only be installed and commissioned by an authorised specialist company.
Technical data
| Code | CX10C0000008 |
| Manufacturer | IVAR |
| Type | IVAR.M16-RMP |
| Product kind | solenoid valve, normally closed (NC) |
| Flange connection | DN 100 (ISO 7005 / EN 1092-1) |
| Max. pressure | PN 6 |
| Ambient temperature | -20 to +60 °C |
| Supply | 230 V, 50 – 60 Hz |
| Protection | IP65 |
| Closing time | < 1 s |
| Body material | die-cast aluminium, NBR and Viton seals |
| Medium | non-aggressive dry gases of families I–III: natural gas, CO, LPG |
| Function | gas shut-off on a detector signal, manual reopening (reset) |
Frequently asked questions
Is the valve CX10C0000008 open or closed without voltage?
Closed (NC). It opens while the coil is powered and closes without voltage, also in a mains power cut.
How is the valve reopened after closing?
By hand (reset), once the cause of the leak has been found. According to the data sheet only under voltage and with no alarm from the detector.
Which gases is the valve designed for?
For non-aggressive dry gases of families I, II and III, for example natural gas, carbon monoxide and LPG.
Additional parameters
| Category: | IVAR.M16-RM, RMO, RMP, RMOP - solenoid valves |
|---|---|
| Warranty: | 2 years |
| Code: | CX10C0000008 |
| Manufacturer: | IVAR |
| Type: | IVAR.M16-RMP |
| Product kind: | solenoid valve, normally closed (NC) |
| Flange connection: | DN 100 (ISO 7005 / EN 1092-1) |
| Max. pressure: | PN 6 |
| Ambient temperature: | -20 to +60 °C |
| Supply: | 230 V, 50 – 60 Hz |
| Protection: | IP65 |
| Closing time: | < 1 s |
| Body material: | die-cast aluminium, NBR and Viton seals |
| Medium: | non-aggressive dry gases of families I–III: natural gas, CO, LPG |
| Function: | gas shut-off on a detector signal, manual reopening (reset) |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
