PAW.HD950 hydraulic separator for horizontal distribution manifold DN 20, up to 950 l/h – SALE

Code: 3142
Action
Not rated Rating details
592,86 € –10 %
Hydraulický oddeľovač PAW.HD950 pre horizontálny distribučný rozdeľovač DN 20, do 950 l/h – AKCIA
592,86 € –10 % 533,57 € / pcs 433,80 € excl. VAT Measure price:
International delivery
In stock at supplier

Detailed information

Product detailed description

The PAW.HD950 (code 3142) is a hydraulic separator from the PAW system for installations with a DN 20 horizontal distribution manifold. It balances pressures and flow rates between the primary heat source circuit and the secondary consumer circuits, so the pumps of the individual circuits do not affect each other. The boiler circuit then runs at a constant flow rate and the heating circuits at a variable one.

Connection and installation

  • heat source side: 3/4" female or 1" male thread with flat seal
  • system side: 3/4" PAW flange for a 1" union nut – directly onto the PAW.MV 20 manifold
  • 2 x 3/4" female ends with plugs, for example for a temperature sensor or a drain ball valve
  • mounting horizontally below the triple PAW.MV manifold, vertically, or on its own in the pipework (2 nuts code 2055 are then required)

Design

  • brass body, EPDM seals, design EPP insulation
  • width 430 mm, height 80 mm, connection centre distance 90 mm
  • supplied with separator body, insulation, union nuts and sealing plugs

When a separator is used, the primary circuit and every secondary circuit must have their own circulation pump. EPDM seals must not come into contact with substances containing mineral oils. Optional accessories include PAW.DR 3121 wall brackets and the PAW.KEX 7509 expansion vessel connection kit.

Technical data

Code3142
ManufacturerPAW
TypePAW.HD950
Nominal sizeDN 20
Recommended flow rateup to 950 l/h
Max. operating pressure6 bar
Max. operating temperature+110 °C
Heat source connection3/4" female or 1" male
Manifold connectionPAW flange 3/4", 1" union nut
Side connections2 x 3/4" female with plug
Dimensions (W x H)430 x 80 mm
Connection centre distance90 mm
Materialbrass, EPP insulation, EPDM seals

Frequently asked questions

When is a hydraulic separator needed?
When the system has a pump on the heat source side and pumps in the consumer circuits that must not influence each other. Every circuit, primary and secondary, needs its own circulation pump.

Can the PAW.HD950 be installed without a manifold?
Yes, the separator can be fitted on its own in the pipework; two union nuts code 2055 are then needed. It works in both horizontal and vertical position.

How is the separator connected when mounted vertically?
The heating circuits connect to the upper connection and the boiler circuit to the lower one. The drain ball valve is then fitted in the bottom end, the lowest point.

Additional parameters

Category: hydraulic separators
Warranty: 2 years
Code: 3142
Manufacturer: PAW
Type: PAW.HD950
Nominal size: DN 20
Recommended flow rate: up to 950 l/h
Max. operating pressure: 6 bar
Max. operating temperature: +110 °C
Heat source connection: 3/4" female or 1" male
Manifold connection: PAW flange 3/4", 1" union nut
Side connections: 2 x 3/4" female with plug
Dimensions (W x H): 430 x 80 mm
Connection centre distance: 90 mm
Material: brass, EPP insulation, EPDM seals

Product rating

Be the first who will post an article to this item!

Do not fill out this field

How would you rate this product? Choose 1 to 5 stars, where 1 is the worst and 5 is the best rating.

Discussion

Be the first who will post an article to this item!

Do not fill out this field
Vytvořil Shoptet | Design Shoptak.cz.