IVAR.ELCHO-5000 – above-ground plastic tank for drinking water and rainwater, 5000 l – SALE
Code: A580080Product detailed description
The IVAR.ELCHO-5000 (code A580080) is an above-ground plastic tank with a capacity of 5000 litres, made as a self-supporting polyethylene monobloc. It is used to store drinking water or rainwater for later use and as a break tank for booster sets or ahead of further treatment of the water entering the building's pipework.
Design
The horizontal cylindrical LHDPE body stands on feet; its diameter is 1700 mm, overall length 2310 mm and overall height 1840 mm. The filler cap is Ø 455 mm and the inspection opening Ø 400 mm. At the bottom there is a 3/4" connection, two further 2" connections (lower and upper) and a Ø 28 mm opening at the top. The PPH polypropylene fittings have rubber seals and nylon ring nuts; the filler cap and vent plug are made of LHDPE.
- the tank material has a hygiene certificate – it can be used for drinking water if the installation complies with the applicable regulations
- operating temperature range −50 to +60 °C
- UV-resistant resin, so even a tank exposed to sunlight does not encourage algae
- liquids other than water only after consulting the supplier
Installation and maintenance
Place the tank on a level surface able to carry the weight of the full tank, away from heat sources, and provide drainage in case water escapes. It may only be moved when empty. The overflow opening must be sealed so that no light enters the tank. Several tanks are connected with flexible pipes, an expansion joint and a pipe support; leave 500–600 mm between tanks and 200–250 mm from the wall so they can expand freely while filling. Clean the inside as needed every 5–10 years and check the joints for tightness.
Technical data
| Code | A580080 |
| Manufacturer | IVAR |
| Type | IVAR.ELCHO-5000 |
| Capacity | 5000 l |
| Installation | above ground, self-supporting |
| Tank material | LHDPE polyethylene |
| Dimensions | Ø 1700 mm, length 2310 mm, height 1840 mm |
| Inspection opening | Ø 400 mm |
| Filler cap | Ø 455 mm, LHDPE |
| Connections | 1 × 3/4" + 2 × 2", Ø 28 mm opening |
| Operating temperature | −50 to +60 °C |
| Drinking water | material with hygiene certificate |
Frequently asked questions
Can I store drinking water in the ELCHO-5000 tank?
Yes, the tank material has a hygiene certificate for drinking water. However, it may only be used for drinking water if the installation complies with the applicable regulations.
Can the tank stand in the sun?
The tank is designed for above-ground installation and its material is UV-resistant, so no algae form even in the sun. It is important to seal the overflow opening against light.
How are several tanks connected?
With flexible pipes, an expansion joint and a pipe support. Leave 500–600 mm between tanks and 200–250 mm from the wall so they can expand freely while filling.
Additional parameters
| Category: | IVAR.ELCHO - above-ground plastic tanks |
|---|---|
| Warranty: | 2 years |
| Code: | A580080 |
| Manufacturer: | IVAR |
| Type: | IVAR.ELCHO-5000 |
| Capacity: | 5000 l |
| Installation: | above ground, self-supporting |
| Tank material: | LHDPE polyethylene |
| Dimensions: | Ø 1700 mm, length 2310 mm, height 1840 mm |
| Inspection opening: | Ø 400 mm |
| Filler cap: | Ø 455 mm, LHDPE |
| Connections: | 1 × 3/4" + 2 × 2", Ø 28 mm opening |
| Operating temperature: | −50 to +60 °C |
| Drinking water: | material with hygiene certificate |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
