IVAR.RAIN BASIC CU-3000 KOMPLET DTRON – 3000 l underground rainwater tank with pump – SALE

Code: A520074D3
Action
Not rated Rating details
4 351,74 € –44 %
IVAR.RAIN BASIC CU-3000 KOMPLET DTRON – podzemná nádrž 3000 l na dažďovú vodu s čerpadlom – AKCIA
4 351,74 € –44 % 2 423,47 € / pcs 1 970,30 € excl. VAT Measure price:
International delivery
In stock at supplier

Detailed information

Product detailed description

The IVAR.RAIN BASIC CU-3000 KOMPLET DTRON (code A520074D3, designation ELCU-3000 l KOMPLET) is a ready-made kit for collecting and using rainwater. It contains a self-supporting underground polyethylene tank of 3000 litres, a cleaning filter, the DAB DTRON3 X 45/90 submersible pump and the Com Box control unit. Rainwater can thus be used, for example, for toilet flushing, the washing machine, garden watering or cleaning; the tank is not intended for drinking water.

DTRON3 X 45/90 pump and Com Box

This compact single-phase submersible pump, 185 mm in diameter, has an integrated pressure vessel and electronics – it starts by itself on demand, stops afterwards and is protected against dry running and too frequent starts. The X version draws clean water from below the surface through a floating suction strainer. Maximum flow 6 m³/h, maximum head 45 m, G 1 1/4" connection and 15 m cable. The Com Box control unit is used to monitor and set up the pump. Have the electrical connection made by a professional.

3000 l tank

  • diameter 1585 mm, overall height 2220 mm, length 1920 mm
  • DN 110 rainwater inlet at 1365 mm height, DN 110 overflow at 1310 mm and DN 110 suction of filtered water
  • 2" vent, extension and inspection opening Ø 500 mm
  • tank, extension, cover and filter in LLDPE polyethylene, pipes in PVC; the upper extension and cover are factory-fitted
  • temperature range −50 to +60 °C

Installation and maintenance

Before installation, the hydrogeological and morphological characteristics of the site must be assessed. The pit needs at least 30 cm of free space around the tank (50 cm in clay soil), must be at least 1 m from buildings and needs a sand bed at least 15 cm thick at the bottom. Backfill with sand in layers of 15–20 cm while gradually filling the tank with water. The backfill above the top of the tank must not exceed 80 cm, and without a load-bearing reinforced concrete slab, vehicles must not pass closer than 2 m to the pit. Route the vent above the highest point of the building. Clean the filter inside the tank regularly, check the clarity and smell of the water and clean the whole tank every 5–10 years. Installation must be carried out by a qualified technician.

Technical data

CodeA520074D3
ManufacturerIVAR
TypeIVAR.RAIN BASIC CU-3000 KOMPLET
Capacity3000 l
Installationunderground, self-supporting
Userainwater (not drinking water)
Diameter / height / length1585 / 2220 / 1920 mm
Inlet / overflow / suctionDN 110 / DN 110 / DN 110
Vent2"
Inspection openingØ 500 mm
MaterialLLDPE polyethylene, PVC pipes
Operating temperature−50 to +60 °C
PumpDAB DTRON3 X 45/90 (6 m³/h, 45 m) + Com Box

Frequently asked questions

What does the RAIN BASIC CU-3000 KOMPLET DTRON kit contain?
An underground tank of 3000 litres, a cleaning filter, the DAB DTRON3 X 45/90 submersible pump and the Com Box control unit.

What is the Com Box unit for?
For monitoring and setting up the DTRON3 pump. The pump switches according to demand, is protected against dry running and delivers up to 6 m³/h at a head of up to 45 m.

Is the water in the tank drinkable?
No, the tank is meant for retaining rainwater, not drinking water. It is suitable for toilet flushing, the washing machine, garden watering and cleaning.

Additional parameters

Category: IVAR.RAIN BASIC CU - plastic tank for rainwater use
Warranty: 2 years
Code: A520074D3
Manufacturer: IVAR
Type: IVAR.RAIN BASIC CU-3000 KOMPLET
Capacity: 3000 l
Installation: underground, self-supporting
Use: rainwater (not drinking water)
Diameter / height / length: 1585 / 2220 / 1920 mm
Inlet / overflow / suction: DN 110 / DN 110 / DN 110
Vent: 2"
Inspection opening: Ø 500 mm
Material: LLDPE polyethylene, PVC pipes
Operating temperature: −50 to +60 °C
Pump: DAB DTRON3 X 45/90 (6 m³/h, 45 m) + Com Box

Product rating

Be the first who will post an article to this item!

Do not fill out this field

How would you rate this product? Choose 1 to 5 stars, where 1 is the worst and 5 is the best rating.

Discussion

Be the first who will post an article to this item!

Do not fill out this field

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.