PRESS coupling stainless steel AISI 304 – 108 mm – IVAR.IVN410
Code: IVN410.108Product detailed description
IVAR.IVN410 – 108 mm (code IVN410.108) is a non-reducing coupling with two press ends (PRESS × PRESS) for joining two sections of stainless steel pipe of the same 108 mm diameter. The joint is made by mechanically pressing the fitting.
Applications
- closed heating and cooling systems, solar systems
- compressed air and vacuum systems
- inert and technical gases, technical and process fluids
- industrial applications, waste water and rainwater
Note: not for drinking water. The fitting body is marked with the AISI 304 logo, a symbol indicating that it is unsuitable for drinking water, the size and a traceability code.
Technical data
- material: AISI 304 stainless steel (W.Nr. 1.4301), EPDM sealing O-ring
- max. operating pressure PN 16, vacuum down to -0.8 bar (absolute pressure 0.2 bar)
- operating temperature -20 °C to +85 °C, maximum +120 °C
- antifreeze content in the system max. 50%
- length L 196 mm and dimension Z 42 mm according to the technical drawing
Installation
Cut the pipe square to its axis with a pipe cutter or a fine-toothed saw and carefully deburr it inside and out. Mark the insertion depth with a marker pen, check the position of the O-ring and push the fitting on axially with a slight twist up to the stop – water may be used to help, but never oil or lubricants. For the 108 mm diameter, M-profile press chains with at least three segments and suitable adapter jaws are required. The joint must be pressed right the first time; pressing it again may damage the seal.
For the 108 mm diameter, neither the colour strip nor the LBP O-ring is supplied (only for sizes 15 – 54 mm). Pressing is complete when the end faces of the chain segments touch; before pressing, the manufacturer recommends fixing the pipes and fitting in clamping vices so that they are perfectly aligned.
Before commissioning, flush the entire system according to the manufacturer's instructions; for treating the heating system IVAR recommends GEL.LONG LIFE 100. Follow the installation and operating manual of the IVAR.PRESS system during installation.
Technical data
| Code | IVN410.108 |
| Manufacturer | IVAR |
| Type | IVAR.IVN410 |
| Design | coupling PRESS × PRESS, non-reducing |
| Pipe diameter d | 108 mm |
| Length L / dimension Z | 196 / 42 mm |
| Max. operating pressure | PN 16 |
| Max. vacuum | -0.8 bar (absolute pressure 0.2 bar) |
| Operating temperature | -20 °C to +85 °C, max. +120 °C |
| Material | stainless steel AISI 304 (W.Nr. 1.4301) |
| Seal | EPDM O-ring |
| Press jaws | M profile, press chain (min. 3 segments) |
| Press indicator | none |
| Antifreeze | max. 50% |
| Drinking water | not suitable |
Frequently asked questions
Can the IVAR.IVN410 coupling be used for drinking water?
No. The AISI 304 stainless steel fitting is not intended for drinking water, as a symbol on its body also indicates. It is used, for example, in closed heating and cooling circuits, solar systems or compressed air networks.
Which press jaws do I need for the 108 mm size?
For the 108 mm diameter you need M-profile press chains with at least three segments, together with suitable adapter jaws. The manufacturer does not accept pressing with standard jaws for this size.
Does the 108 mm coupling have a press indicator?
No, the colour strip and the LBP O-ring are only supplied for sizes 15 to 54 mm. Pressing is complete when the end faces of the chain segments touch each other.
Can the circuit contain antifreeze?
Yes, the antifreeze concentration may be up to 50%. The operating temperature is -20 °C to +85 °C, maximum +120 °C, at pressures up to PN 16.
Additional parameters
| Category: | IVAR.IVN10,IVN11 - Coupling |
|---|---|
| Warranty: | 2 years |
| Code: | IVN410.108 |
| Manufacturer: | IVAR |
| Type: | IVAR.IVN410 |
| Design: | coupling PRESS × PRESS, non-reducing |
| Pipe diameter d: | 108 mm |
| Length L / dimension Z: | 196 / 42 mm |
| Max. operating pressure: | PN 16 |
| Max. vacuum: | -0.8 bar (absolute pressure 0.2 bar) |
| Operating temperature: | -20 °C to +85 °C, max. +120 °C |
| Material: | stainless steel AISI 304 (W.Nr. 1.4301) |
| Seal: | EPDM O-ring |
| Press jaws: | M profile, press chain (min. 3 segments) |
| Press indicator: | none |
| Antifreeze: | max. 50% |
| Drinking water: | not suitable |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
