PNI SVM2000VA servo-motor voltage stabiliser, 2000 VA / 1600 W, 230 V output
Code: PNI-SVM-2KProduct detailed description
The PNI SVM2000VA is a single-phase voltage stabiliser with a servo motor. When the mains voltage fluctuates, it automatically brings it back as close as possible to the set value of 230 V, so your appliances run under steady conditions. It handles a power of 1600 W (2000 VA) at a current of 7.2 A.
Servo-motor stabilisers work smoothly, without distorting the sine wave, and have a long service life. You can connect an air conditioner, a fridge, a TV, power tools or other household appliances to it. The coil is made of pure copper, which extends its service life and improves efficiency.
On the rear panel there is a terminal block with one input and two outputs (L / N / PE). The device has an automatic circuit-breaker switch and protects against overload, short circuit, overheating, overvoltage and undervoltage; it also has a start-up delay. Ventilation openings on the sides carry the heat away.
Installation
The stabiliser is connected to the mains and to the appliances via the terminal block – the supply cable is not included in the package. Connection to 230 V must be carried out by a person with electrical qualifications. The dimensions are 235 × 260 × 180 mm and the weight is 8.6 kg.
Frequently asked questions
What is the difference compared with a relay stabiliser?
A servo-motor type regulates the voltage smoothly, not in steps, so it is suitable where switching steps are a problem.
Is a cable included in the package?
No, the cable must be chosen according to the way of connection.
What if the load is higher than 1600 W?
The overload protection switches the device off. Choose a larger model.
Technical specifications
| Brand | PNI |
| Manufacturer code | PNI-SVM-2K |
| EAN | 5949066524509 |
| Type | Single-phase servo-motor voltage stabiliser |
| Power | 2000 VA / 1600 W |
| Current | 7.2 A |
| Input voltage | 170–260 V AC, 50/60 Hz |
| Output voltage | 230 V |
| Connection | terminal block L / N / PE: 1 input, 2 outputs |
| Output waveform | sine wave, no distortion |
| Protections | overload, short circuit, overheating, overvoltage, undervoltage, start-up delay, mechanical fault |
| Humidity | ≤ 90% |
| Dimensions | 235 × 260 × 180 mm |
| Package contents | stabiliser, manual (supply cable not included) |
| Weight | 8.56 kg |
| Warranty | 24 months |
| Country of origin | China |
Additional parameters
| Category: | Backup Power Supplies - Boilers, Pumps |
|---|---|
| Warranty: | 2 years |
| Weight: | 8.56 kg |
| EAN: | 5949066524509 |
| Brand: | PNI |
| Manufacturer code: | PNI-SVM-2K |
| EAN: | 5949066524509 |
| Type: | Single-phase servo-motor voltage stabiliser |
| Power: | 2000 VA / 1600 W |
| Current: | 7.2 A |
| Input voltage: | 170–260 V AC, 50/60 Hz |
| Output voltage: | 230 V |
| Connection: | terminal block L / N / PE: 1 input, 2 outputs |
| Output waveform: | sine wave, no distortion |
| Protections: | overload, short circuit, overheating, overvoltage, undervoltage, start-up delay, mechanical fault |
| Humidity: | ≤ 90% |
| Dimensions: | 235 × 260 × 180 mm |
| Package contents: | stabiliser, manual (supply cable not included) |
| Weight: | 8.56 kg |
| Warranty: | 24 months |
| Country of origin: | China |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!