IVAR.ELCHU-2000 underground plastic tank, 2000 l, horizontal, for drinking water and rainwater
Code: A590070Product detailed description
The IVAR.ELCHU-2000 (code A590070) is a horizontal cylindrical tank with a capacity of 2000 l designed for underground installation. It stores drinking water or rainwater for further use in the building and can also serve as a break tank upstream of a booster set or of further treatment of the water supplied to the internal pipework.
Design and dimensions
- self-supporting monobloc made of LLDPE polyethylene with a hygiene certificate for drinking water
- temperature range from −50 °C to +60 °C
- diameter 1300 mm, height 1800 mm, length 1700 mm
- DN 400 inspection opening and extension with 500 mm diameter and 415 mm height
- extension and inlet cover are factory-fitted
Burying the tank
The pit should leave at least 30 cm of free space around the tank (50 cm in clay soil) and be at least 1 m away from buildings. A layer of sand at least 15 cm thick is spread on the bottom. Backfilling is done gradually in layers of 15–20 cm, alternating water into the tank and sand into the pit. The soil cover above the top of the tank must not exceed 80 cm. Under a driveway, a self-supporting reinforced concrete slab designed by a specialist is required above the tank. Installation should be carried out by a qualified company.
The tank may only be used for drinking water if the entire installation complies with the applicable regulations. Use with liquids other than water must be agreed with the supplier in advance.
Technical data
| Code | A590070 |
| Manufacturer | IVAR |
| Type | IVAR.ELCHU-2000 |
| Capacity | 2000 l |
| Installation | underground, horizontal cylindrical tank |
| Material | LLDPE polyethylene (monobloc) |
| Tank diameter | 1300 mm |
| Height | 1800 mm |
| Length | 1700 mm |
| Inspection opening | DN 400 |
| Extension | Ø 500 mm, height 415 mm |
| Temperature range | −50 to +60 °C |
| Drinking water | material with hygiene certificate |
Frequently asked questions
Is the tank also suitable for drinking water?
Yes, the tank material has a hygiene certificate for drinking water. However, it may only be used for drinking water if the entire installation complies with the applicable regulations.
How deep can the tank be buried?
The soil layer above the top of the tank may be at most 80 cm. The factory-fitted extension brings the inspection opening up to ground level.
Can a car drive over the tank?
Only with additional measures: under a driveway, a self-supporting reinforced concrete slab designed by a specialist must be built above the tank. An air gap of at least 10 cm must remain between the slab and the tank.
Additional parameters
| Category: | IVAR.ELCHU - below-ground plastic tanks |
|---|---|
| Warranty: | 2 years |
| Code: | A590070 |
| Manufacturer: | IVAR |
| Type: | IVAR.ELCHU-2000 |
| Capacity: | 2000 l |
| Installation: | underground, horizontal cylindrical tank |
| Material: | LLDPE polyethylene (monobloc) |
| Tank diameter: | 1300 mm |
| Height: | 1800 mm |
| Length: | 1700 mm |
| Inspection opening: | DN 400 |
| Extension: | Ø 500 mm, height 415 mm |
| Temperature range: | −50 to +60 °C |
| Drinking water: | material with hygiene certificate |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
