Equal tee 90° press fitting IVAR.IVN440 – stainless steel AISI 304, 108 mm

Code: IVN440.108
Not rated Rating details
314,88 € –20 %
T-kus 90° jednoznačný PRESS IVAR.IVN440 – nerez AISI 304, 108 mm
314,88 € –20 % 251,90 € / pcs 204,80 € excl. VAT Measure price:
International delivery
In stock at supplier

Detailed information

Product detailed description

IVAR.IVN440 – 108 mm (code IVN440.108) is an equal 90° tee made of AISI 304 (1.4301) stainless steel. All three ends, on the run and on the branch, are press sockets (PRESS × PRESS × PRESS) for pipe with an outside diameter of 108 mm, so you can take a perpendicular branch of the same size off a continuous line.

Suitable systems

  • closed heating and cooling systems, solar circuits
  • compressed air and vacuum systems
  • inert and technical gases, technical and process fluids
  • industrial applications, waste water and rainwater

This tee is not intended for drinking water. Its body is marked with the AISI 304 logo, the size, a traceability code and a symbol indicating that it is unsuitable for drinking water.

Pressing the 108 mm size

For diameters from 42 to 108 mm, the manufacturer only accepts M-profile press chains with at least three segments, usually with an adapter; pressing with standard one-piece jaws is not recognised. The V profile is prohibited for any diameter. The 108 mm size belongs to the so-called large diameters: it requires a high-force press tool (over 40 kN), and before pressing it is recommended to secure the pipes and the fitting in installation clamps so that they are perfectly aligned. The LBP O-ring and the coloured press indicator are not supplied in this size (the range offers them only from 15 to 54 mm), so each joint must be checked visually – pressing is complete when the end faces of the chain segments touch each other.

Cut the pipe square to its axis, deburr it inside and out and moisten the O-ring with water at most, never with oil or grease. Push the pipe in with a slight twist up to the stop, mark the insertion depth with a marker and press the joint first time.

Technical data

  • maximum operating pressure PN 16, vacuum down to -0.8 bar (absolute pressure 0.2 bar)
  • operating temperature -20 °C to +85 °C, maximum +120 °C
  • antifreeze mixture with a concentration of up to 50 %
  • material: AISI 304 (1.4301) stainless steel, EPDM sealing O-ring
  • dimensions as per drawing: L 312 mm, L1 154 mm, Z 79 mm, Z1 77 mm, I 156 mm

For a smaller or threaded branch, the same range offers the tees IVAR.IVN441 (reducing) and IVAR.IVN442 (with female thread). Flush the entire heating system before commissioning – for its treatment IVAR recommends GEL.LONG LIFE 100.

Technical data

CodeIVN440.108
ManufacturerIVAR
TypeIVAR.IVN440
Fitting typetee 90°, equal, PRESS × PRESS × PRESS
Pipe diameter (d)108 mm
Overall length (L)312 mm
Branch height (L1)154 mm
Dimensions Z / Z1 / I79 / 77 / 156 mm
Materialstainless steel AISI 304 (1.4301)
SealEPDM O-ring
Max. operating pressurePN 16
Operating temperature-20 °C to +85 °C, max. +120 °C
Press jawsM profile, chain (min. 3 segments)
Press indicatorno
Drinking waternot suitable

Frequently asked questions

Can I use the IVAR.IVN440 tee for drinking water?
No. The AISI 304 stainless steel fittings in this range are not intended for drinking water, as a symbol on their body also indicates. They are suitable for closed heating and cooling circuits, solar systems, compressed air and technical gases.

Which press jaws do I need for the 108 mm size?
M-profile press chains with at least three segments, usually with an adapter. The manufacturer does not accept one-piece jaws from 42 mm upwards, and the V profile is prohibited.

How can I tell that a joint has not been pressed yet?
In the 108 mm size there is no LBP O-ring or coloured indicator, so check every joint visually. Pressing is complete when the end faces of the press chain segments touch.

Can a smaller branch be taken off the IVAR.IVN440 108 mm tee?
No, it is an equal tee – all three sockets are 108 mm. For a smaller branch, the range offers the reducing tee IVAR.IVN441.

Additional parameters

Category: IVAR.IVN40, IVN41 - T-pieces
Warranty: 2 years
Code: IVN440.108
Manufacturer: IVAR
Type: IVAR.IVN440
Fitting type: tee 90°, equal, PRESS × PRESS × PRESS
Pipe diameter (d): 108 mm
Overall length (L): 312 mm
Branch height (L1): 154 mm
Dimensions Z / Z1 / I: 79 / 77 / 156 mm
Material: stainless steel AISI 304 (1.4301)
Seal: EPDM O-ring
Max. operating pressure: PN 16
Operating temperature: -20 °C to +85 °C, max. +120 °C
Press jaws: M profile, chain (min. 3 segments)
Press indicator: no
Drinking water: not suitable

Product rating

Be the first who will post an article to this item!

Do not fill out this field

How would you rate this product? Choose 1 to 5 stars, where 1 is the worst and 5 is the best rating.

Discussion

Be the first who will post an article to this item!

Do not fill out this field

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.