Reducing tee PRESS-PPSU 32x26x32 mm – IVAR.TR PPSU
Code: 82832360Product detailed description
IVAR.TR PPSU 32x26x32 (code 82832360) is a reducing tee from the IVAR.PRESS system for press connections of ALPEX and TURATEC multilayer pipes and PEX pipes. The run is 32 mm at both ends and the branch is reduced to 26 mm, so a smaller branch line can be taken off the main pipe – for example to radiators or draw-off points.
Design and materials
- body made of PPSU plastic (polyphenylsulfone) with high resistance to corrosion and deposits
- press sleeves made of AISI 304 stainless steel, sealing by EPDM O-rings
- polycarbonate positioning rings with inspection windows showing whether the pipe is inserted correctly
- hygiene certificate for drinking water; used for radiator connections, underfloor heating and sanitary installations
Installation
- cut the pipe square, then calibrate and deburr it with original IVAR tools (e.g. IVAR.UNI or IVAR.UNIK)
- push the tee onto the pipe axially without twisting – water makes it easier, do not use oil or any other lubricant
- radial pressing using B or F contour press jaws matching the socket diameter
- the joint can be pressurised immediately after pressing and no open flame is needed
An unpressed joint gives itself away: during a pressure test between 1 and 6.5 bar water escapes from it, so the mistake is found before the pipework is covered. The press joints may also be located in inaccessible places – in floors, shafts or under plaster. Dimensions L1 / L2 / L3 according to the manufacturer's technical drawing are 51 / 54 / 51 mm, weight 96 g. Follow the manufacturer's instructions for joining pipes with IVAR.PRESS fittings during installation.
Technical data
| Code | 82832360 |
| Manufacturer | IVAR |
| Type | IVAR.TR PPSU |
| Design | press tee, reducing |
| Size D1 × D2 × D3 | 32 × 26 × 32 mm |
| Suitable pipes | ALPEX, TURATEC, PEX |
| Max. operating pressure | PN 10 |
| Temperature range | +3 °C to +95 °C |
| Press jaws | B or F contour |
| Pressing principle | radial |
| Body material | PPSU (polyphenylsulfone) |
| Press sleeve | stainless steel AISI 304 |
| Seal | EPDM O-ring |
| Dimensions L1 / L2 / L3 | 51 / 54 / 51 mm |
| Weight | 96 g |
Frequently asked questions
How are the dimensions of the 32x26x32 tee read?
The first and last numbers give the run diameter, here 32 mm at both ends, the middle one the branch diameter (26 mm). All sockets are intended for ALPEX, TURATEC or PEX pipes.
Can the tee be used for drinking water?
Yes, the fitting has a hygiene certificate for drinking water. It is also suitable for heating – radiator connections and underfloor heating – up to PN 10 and between +3 and +95 °C.
Which press jaws do I need?
All sockets of this tee (26 and 32 mm) are pressed with B or F contour jaws. The pressing tool and jaws must be approved by the manufacturer of the IVAR.PRESS system.
How do I check that the joint is pressed correctly?
Before pressing, check in the windows of the positioning ring that the pipe is inserted fully up to the stop. If a joint is left unpressed, it leaks during the pressure test between 1 and 6.5 bar.
Additional parameters
| Category: | T-pieces press - PPSU, reduced |
|---|---|
| Warranty: | 2 years |
| Weight: | 0.096 kg |
| Code: | 82832360 |
| Manufacturer: | IVAR |
| Type: | IVAR.TR PPSU |
| Design: | press tee, reducing |
| Size D1 × D2 × D3: | 32 × 26 × 32 mm |
| Suitable pipes: | ALPEX, TURATEC, PEX |
| Max. operating pressure: | PN 10 |
| Temperature range: | +3 °C to +95 °C |
| Press jaws: | B or F contour |
| Pressing principle: | radial |
| Body material: | PPSU (polyphenylsulfone) |
| Press sleeve: | stainless steel AISI 304 |
| Seal: | EPDM O-ring |
| Dimensions L1 / L2 / L3: | 51 / 54 / 51 mm |
| Weight: | 96 g |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
