IVAR.PUFFER PSS 300 buffer tank for heating and chilled water – 277 l – SALE
Code: 1V1930DProduct detailed description
Buffer tank for heating and cooling
The IVAR.PUFFER PSS 300 holds 277 litres of water and acts in a closed system as a balancing vessel between the heat source and the heating circuit. It stores heat from a boiler, heat pump, fireplace insert or solar system and can equally be integrated into a cooling circuit. There is no internal coil and no flange – the heat source and the emitters are connected directly to the tank sockets.
Design and connections
- steel vessel without internal coating, painted on the outside
- rigid PU foam insulation, 50 mm (energy class C)
- four 2" sockets for flow and return of the heat source and the heating system
- 5/4" air vent at the top, 3/4" drain
- 1/2" sockets for a thermometer and a temperature sensor
- 6/4" socket for an electric immersion heater
Installation and operation
The tank must be installed by a qualified company in an enclosed, ventilated room where the temperature stays at least +5 °C all year round. It stands upright on a level floor with sufficient load-bearing capacity; allow for the tilt height of 1700 mm when handling it. The limits of 6 bar and 95 °C must be secured by a safety valve, an expansion vessel and temperature limitation at the heat source. An electric immersion heater is intended only for emergency back-up and must not be the sole permanent heat source.
Technical data
| Code | 1V1930D |
| Manufacturer | IVAR |
| Type | IVAR.PUFFER PSS 300 |
| Total capacity | 277 l |
| Thermal insulation | rigid PU foam insulation, 50 mm (energy class C) |
| Total height with insulation | 1560 mm |
| Diameter with insulation | 600 mm |
| Tilt height | 1700 mm |
| Empty weight | 55 kg |
| Max. operating pressure | 6 bar |
| Max. operating temperature | 95 °C |
| Heat source and system connections | 4 × 2" |
| Socket for electric heater | 6/4" |
Frequently asked questions
Can the IVAR.PUFFER PSS 300 tank also be used in a cooling circuit?
Yes, the PSS series is designed for closed heating and cooling systems. The maximum operating pressure is 6 bar and the temperature 95 °C.
Can I fit an electric immersion heater in the tank?
Yes, the tank has a 6/4" socket for this. According to the manufacturer the heater is only an emergency back-up and must not be the sole permanent heat source.
What maintenance does the tank need?
The tank must be desludged internally once every 12 months. During operation, pressures, temperature, the safety valve and the gas pre-charge of the expansion vessel are checked regularly.
Additional parameters
| Category: | for heating and cooling |
|---|---|
| Warranty: | 2 years |
| Weight: | 55 kg |
| Code: | 1V1930D |
| Manufacturer: | IVAR |
| Type: | IVAR.PUFFER PSS 300 |
| Total capacity: | 277 l |
| Thermal insulation: | rigid PU foam insulation, 50 mm (energy class C) |
| Total height with insulation: | 1560 mm |
| Diameter with insulation: | 600 mm |
| Tilt height: | 1700 mm |
| Empty weight: | 55 kg |
| Max. operating pressure: | 6 bar |
| Max. operating temperature: | 95 °C |
| Heat source and system connections: | 4 × 2" |
| Socket for electric heater: | 6/4" |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
