Axial Fan IVAR.ASPIRANTE HT with Hygrostat and Timer – for Pipe Ø 80/100/120 mm, 230 V
Code: IVAP3104Product detailed description
The fan IVAR.ASPIRANTE HT (code IVAP3104) is used for intermittent and continuous air extraction from bathrooms, kitchens and technical rooms in apartments, houses and commercial spaces. It blows air directly out through the wall or into a ventilation shaft and with the set IVAP0900 it can also be mounted in a window or glazed panel.
Features
- connection to duct Ø 80, 100 or 120 mm – three adapters and a check valve are included in the package
- airflow 55–130 m³/h depending on the duct diameter
- cover made of impact-resistant ABS plastic resistant to UV radiation
- induction motor with thermal fuse, insulation class F, double insulation (class II)
- protection class IPX4, maximum air temperature 45 °C, power supply 230 V / 50 Hz
- shortened neck allows connecting a duct bend directly behind the fan
Hygrostat and timer
The fan starts automatically when the relative humidity in the room exceeds the set limit and runs until the humidity drops. After that, the timer allows it to run for an additional 45 s to 20 min. You can set the humidity limit in the range of 40–80 % RH, and the fan can also be started manually.
Mount the fan on a wall or ceiling at least 2.3 m above the floor and connect it via a two-pole switch with a minimum contact gap of 3 mm. It must not extract air through a duct that is used to vent exhaust gases from a gas appliance. Leave the electrical connection to a qualified professional.
Technical specifications
| Code | IVAP3104 |
| Brand | IVAR |
| Type | IVAR.ASPIRANTE HT |
| Type | axial exhaust fan |
| Configuration | with hygrostat and timer |
| Duct diameter | Ø 80 / 100 / 120 mm (adapters included in the package) |
| Airflow | 55–130 m³/h depending on the duct diameter |
| Power supply | 230 V / 50 Hz |
| Protection class | IPX4 |
| Maximum air temperature | 45 °C |
| Cover material | ABS, impact-resistant, UV stable |
| Motor | induction with thermal fuse, insulation class F |
| Run-down time | 45 s – 20 min |
| Humidity setting | 40–80 % RH |
Frequently asked questions
What duct diameter is suitable for the fan?
For ducts Ø 80, 100 or 120 mm. The appropriate adapters and a check valve are part of the package; the adapter for Ø 90 mm can be ordered separately.
Can the fan be mounted in a window?
Yes, with a window mounting set or glazed panel (code IVAP0900), which is suitable for all diameters. The glass can be up to 15 mm thick.
When does the fan turn on automatically?
When the relative humidity in the room exceeds the set value in the range of 40–80 % RH. After the humidity drops, it continues to run for the set time of 45 s to 20 min.
How is the fan cleaned?
After disconnecting from the power supply, wash the dirty parts with water and a neutral cleaning agent. Never immerse electrical components in water.
Additional parameters
| Category: | Forced ventilation with heat recovery |
|---|---|
| Warranty: | 2 years |
| Availability: | In stock or at supplier |
| Code: | IVAP3104 |
| Brand: | IVAR |
| Type: | IVAR.ASPIRANTE HT |
| Product type: | axial extract fan |
| Version: | with humidistat and timer |
| Duct diameter: | Ø 80 / 100 / 120 mm (adapters included) |
| Airflow: | 55–130 m³/h depending on duct diameter |
| Power supply: | 230 V / 50 Hz |
| Protection rating: | IPX4 |
| Max. air temperature: | 45 °C |
| Housing material: | ABS, impact-resistant, UV-stable |
| Motor: | induction motor with thermal fuse, insulation class F |
| Run-on time: | 45 s – 20 min |
| Humidity setting: | 40–80% RH |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.