Axial Fan IVAR.ASPIRANTE T with Run-on Timer – for Pipe Ø 80/100/120 mm, 230 V
Code: IVAP3102Product detailed description
The fan IVAR.ASPIRANTE T (code IVAP3102) is used for intermittent and continuous air extraction from bathrooms, kitchens and technical rooms in apartments, houses and commercial spaces. It exhausts air directly outside through the wall or into a ventilation shaft, and with the set IVAP0900 it can also be mounted in a window or glazed panel.
Features
- connection to duct Ø 80, 100 or 120 mm – three adapters and a check valve are included in the package
- airflow 55–130 m³/h depending on the duct diameter
- cover made of impact-resistant ABS plastic resistant to UV radiation
- induction motor with thermal fuse, insulation class F, double insulation (class II)
- protection class IPX4, maximum air temperature 45 °C, power supply 230 V / 50 Hz
- shortened neck allows connection of a duct bend directly behind the fan
Run-down timer
The fan turns on together with the room light and continues to run for a set time – from 45 seconds to 20 minutes – after the light is turned off. The run-down time is set using a screwdriver on the trimmer on the electronics board; it is factory-set to a minimum of 45 seconds.
Mount the fan on a wall or ceiling at least 2.3 m above the floor and connect it via a two-pole switch with a minimum contact gap of 3 mm. It must not extract air through a duct that is used to vent exhaust gases from a gas appliance. Electrical installation should be carried out by a qualified professional.
Technical specifications
| Code | IVAP3102 |
| Brand | IVAR |
| Type | IVAR.ASPIRANTE T |
| Type | axial exhaust fan |
| Configuration | with run-down timer |
| Duct diameter | Ø 80 / 100 / 120 mm (adapters included in the package) |
| Airflow | 55–130 m³/h depending on the duct diameter |
| Power supply | 230 V / 50 Hz |
| Protection class | IPX4 |
| Maximum air temperature | 45 °C |
| Cover material | ABS, impact-resistant, UV stable |
| Motor | induction with thermal fuse, insulation class F |
| Run-down time | 45 s – 20 min |
Frequently asked questions
What duct diameter is suitable for the fan?
For ducts with a diameter of Ø 80, 100 or 120 mm. The appropriate adapters and a check valve are part of the package; the adapter for Ø 90 mm can be ordered separately.
Can the fan be mounted in a window?
Yes, with a window or glazed panel mounting set (code IVAP0900), which is suitable for all diameters. The glass can be up to 15 mm thick.
How is the run-down time set?
After disconnecting from the power supply, turn the trimmer screw on the electronics board with a screwdriver. The range is 45 s to 20 min; the factory setting is 45 s.
How is the fan cleaned?
After disconnecting from the power supply, wash the dirty parts with water and a neutral cleaning agent. Never immerse electrical components in water.
Additional parameters
| Category: | Forced ventilation with heat recovery |
|---|---|
| Warranty: | 2 years |
| Availability: | In stock or at supplier |
| Code: | IVAP3102 |
| Brand: | IVAR |
| Type: | IVAR.ASPIRANTE T |
| Product type: | axial extract fan |
| Version: | with run-on timer |
| Duct diameter: | Ø 80 / 100 / 120 mm (adapters included) |
| Airflow: | 55–130 m³/h depending on duct diameter |
| Power supply: | 230 V / 50 Hz |
| Protection rating: | IPX4 |
| Max. air temperature: | 45 °C |
| Housing material: | ABS, impact-resistant, UV-stable |
| Motor: | induction motor with thermal fuse, insulation class F |
| Run-on time: | 45 s – 20 min |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.