IVAR.PRESTIGE EP 1000 indirect hot water cylinder with two coils – 930 l
Code: 1Y21A05Product detailed description
Hot water from two heat sources
The IVAR.PRESTIGE EP 1000 storage water heater with 930 l capacity heats and stores domestic hot water by means of two permanently fitted tube coils. The lower coil with 3.0 m² and the upper coil with 1.6 m² are connected to different heat sources – the manufacturer shows, for example, a condensing boiler combined with a solar system. With heating water at 80/60 °C, the lower coil continuously delivers 1.8 m³/h of water heated from 10 to 45 °C according to DIN 4708, the upper coil 1.0 m³/h.
Design
- steel vessel with SMALGLASS internal enamelling to DIN 4753-3 and UNI 10025
- magnesium sacrificial anode against corrosion
- removable soft VLIES polyester-fibre insulation, 100 mm thick, fitted only at the installation site
- inspection flange Ø 180/120 mm
- cold and hot water 5/4", coils 5/4", circulation 1"
- 6/4" socket for an electric immersion heater as emergency back-up
Installation and maintenance
The cylinder is installed upright by a qualified company in an enclosed, ventilated room where the temperature stays above +5 °C all year round. The vessel is rated for max. 10 bar and 95 °C, the coils for 10 bar. The cold water inlet requires a safety valve and an expansion vessel, and a pressure reducing valve if the mains pressure is higher. Every 12 months the cylinder is desludged internally and the anode is checked for wear.
Technical data
| Code | 1Y21A05 |
| Manufacturer | IVAR |
| Type | IVAR.PRESTIGE EP 1000 |
| Total capacity | 930 l |
| Internal coating | SMALGLASS |
| Coil surface upper / lower | 1.6 / 3.0 m² |
| Max. absorbed output upper / lower | 40 / 75 kW |
| Continuous DHW output 80/60 °C, 10/45 °C (DIN 4708) upper / lower | 1.0 / 1.8 m³/h |
| Thermal insulation | soft VLIES 100 mm, energy class C |
| Total height with insulation | 2205 mm |
| Diameter with insulation | 990 mm |
| Empty weight | 239 kg |
| Max. operating pressure vessel / coils | 10 / 10 bar |
| Max. operating temperature of vessel | 95 °C |
| Flange | Ø 180/120 mm |
Frequently asked questions
What are the two coils in the IVAR.PRESTIGE EP 1000 for?
Each coil can be connected to a different heat source, for example the lower one to a solar system and the upper one to a boiler. The lower coil has 3.0 m² of surface, the upper 1.6 m².
What must be installed on the cold water inlet?
A shut-off valve, a check valve, a safety valve set below 10 bar and an expansion vessel; if the mains pressure is higher, also a pressure reducing valve. The manufacturer makes the warranty conditional on fitting the pressure reducing valve and the expansion vessel.
How often should the anode be checked?
The magnesium anode should be checked every 12 months, or every 6 months with more aggressive water. If its diameter falls below 22 mm, it must be replaced.
Additional parameters
| Category: | with two integrated heat exchangers |
|---|---|
| Warranty: | 2 years |
| Weight: | 239 kg |
| Code: | 1Y21A05 |
| Manufacturer: | IVAR |
| Type: | IVAR.PRESTIGE EP 1000 |
| Total capacity: | 930 l |
| Internal coating: | SMALGLASS |
| Coil surface upper / lower: | 1.6 / 3.0 m² |
| Max. absorbed output upper / lower: | 40 / 75 kW |
| Continuous DHW output 80/60 °C, 10/45 °C (DIN 4708) upper / lower: | 1.0 / 1.8 m³/h |
| Thermal insulation: | soft VLIES 100 mm, energy class C |
| Total height with insulation: | 2205 mm |
| Diameter with insulation: | 990 mm |
| Empty weight: | 239 kg |
| Max. operating pressure vessel / coils: | 10 / 10 bar |
| Max. operating temperature of vessel: | 95 °C |
| Flange: | Ø 180/120 mm |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
