IVAR.FEKAFOS 1300 DOUBLE KOMPLET GRI sewage lifting station – 1300 l tank, 2 FEKA VS GRINDER 1000 T-NA pumps, NG PANEL – SALE
Code: DBL1300GRIProduct detailed description
The IVAR.FEKAFOS 1300 DOUBLE KOMPLET GRI (code DBL1300GRI) is a complete lifting station for underground installation. Waste water from the building flows into the 1300 l tank, from where the two pumps push it into the discharge pipe. Non-return valves, a lifting device and level sensing are part of the station.
Tank
The self-supporting tank is rotationally moulded from very strong polyethylene and closed with a gas-tight lid. It is 2000 mm high with an outer diameter of 1020 mm, and the inspection neck has an inner diameter of 625 mm. The inlet uses the supplied connector for smooth PVC sewer pipe DN 160 – the opening is drilled with a hole saw at the marked flat spots. The discharge side is connected with a PE quick coupling in 6/4" (50 mm) or 2" (63 mm), and the pump and float cables are protected by an AFLEX conduit Ø 50 mm connected to the prepared socket.
FEKA VS GRINDER 1000 T-NA pumps and NG PANEL
The two FEKA VS GRINDER 1000 T-NA pumps (3 × 400 V) have a vortex impeller with a front cutting system that shreds solids into small pieces. This allows the sewage to be conveyed through smaller-diameter pressure pipes – a solution used in pressure sewer systems, for example in hilly terrain. The NG PANEL starts the pumps according to the level switches and raises an alarm at high level.
Installation and operation
- excavation about 1 m larger on every side, walls sloped at 15°
- compacted bedding 20–30 cm thick, backfill compacted in 30 cm layers
- with groundwater, a C12/15 concrete base at least 15 cm thick and anchoring of the tank with a stainless-steel strap
- under trafficked areas, a reinforced concrete ring with cast-iron cover that does not bear on the tank (at least 50 mm clearance)
- the neck can be shortened to suit the ground level or raised by up to 50 cm with the S038 (250 mm) or S039 (telescopic, 500 mm) extension
Rainwater, groundwater and swimming-pool water must not be fed into the tank. Installation, electrical connection and commissioning must be carried out by a qualified person.
Technical data
| Code | DBL1300GRI |
| Manufacturer | IVAR |
| Type | IVAR.FEKAFOS KOMPLET |
| Tank volume | 1300 l |
| Tank height | 2000 mm |
| Tank outer diameter | 1020 mm |
| Inspection neck inner diameter | 625 mm |
| Tank material | polyethylene (rotationally moulded) |
| Pumps | 2 × FEKA VS GRINDER 1000 T-NA |
| Pump power supply | 3 × 400 V |
| Control | NG PANEL control unit |
| Inlet | connector for PVC pipe DN 160 |
| Pump impeller | vortex with front cutting system |
Frequently asked questions
When should I choose the GRI version instead of VS?
The GRI version uses FEKA VS GRINDER pumps with a cutting system that shreds solids into small pieces. It suits pressure sewer systems with smaller-diameter discharge pipes, for example in hilly terrain.
Can rainwater be fed into the tank?
No. Only waste water from the building may enter the tank – rainwater, groundwater and water from pools or aquariums must not be fed into it.
What if the tank sits too low below ground level after backfilling?
The neck can be raised by up to 50 cm with the S038 extension (250 mm) or the telescopic S039 extension (500 mm). Before fitting the extension, a rubber seal is placed on the neck of the inspection opening.
How is the tank installed where the groundwater level is high?
A C12/15 concrete base at least 15 cm thick is cast under the tank and the tank is anchored against buoyancy, for example with a stainless-steel strap fixed with M10 or M12 anchors.
Additional parameters
| Category: | DAB.FEKAFOS 280 DOUBLE - automatic pumping stations |
|---|---|
| Warranty: | 2 years |
| Code: | DBL1300GRI |
| Manufacturer: | IVAR |
| Type: | IVAR.FEKAFOS KOMPLET |
| Tank volume: | 1300 l |
| Tank height: | 2000 mm |
| Tank outer diameter: | 1020 mm |
| Inspection neck inner diameter: | 625 mm |
| Tank material: | polyethylene (rotationally moulded) |
| Pumps: | 2 × FEKA VS GRINDER 1000 T-NA |
| Pump power supply: | 3 × 400 V |
| Control: | NG PANEL control unit |
| Inlet: | connector for PVC pipe DN 160 |
| Pump impeller: | vortex with front cutting system |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
