IVAR.FEKAFOS 1300 DOUBLE KOMPLET VS sewage lifting station – 1300 l tank, 2 FEKA VS 1200 T-NA pumps, NG PANEL – SALE

Code: DBL1300VS
Action
Not rated Rating details
7 223,79 € –10 %
Prečerpávacia stanica IVAR.FEKAFOS 1300 DOUBLE KOMPLET VS – nádrž 1300 l, 2 čerpadlá FEKA VS 1200 T-NA, NG PANEL – AKCIA
7 223,79 € –10 % 6 501,41 € / pcs 5 285,70 € excl. VAT Measure price:
International delivery
In stock at supplier

Detailed information

Product detailed description

The IVAR.FEKAFOS 1300 DOUBLE KOMPLET VS (code DBL1300VS) is a complete lifting station for underground installation. Waste water from the building flows into the 1300 l tank, from where the two pumps push it into the discharge pipe. Non-return valves, a lifting device and level sensing are part of the station.

Tank

The self-supporting tank is rotationally moulded from very strong polyethylene and closed with a gas-tight lid. It is 2000 mm high with an outer diameter of 1020 mm, and the inspection neck has an inner diameter of 625 mm. The inlet uses the supplied connector for smooth PVC sewer pipe DN 160 – the opening is drilled with a hole saw at the marked flat spots. The discharge side is connected with a PE quick coupling in 6/4" (50 mm) or 2" (63 mm), and the pump and float cables are protected by an AFLEX conduit Ø 50 mm connected to the prepared socket.

FEKA VS 1200 T-NA pumps and NG PANEL

The two stainless-steel FEKA VS 1200 T-NA sewage pumps (3 × 400 V) have vortex impellers and pass solids up to 50 mm. Their operation is controlled by the NG PANEL according to the level switches; when the maximum level is exceeded it activates an audible signal and the alarm outputs.

Installation and operation

  • excavation about 1 m larger on every side, walls sloped at 15°
  • compacted bedding 20–30 cm thick, backfill compacted in 30 cm layers
  • with groundwater, a C12/15 concrete base at least 15 cm thick and anchoring of the tank with a stainless-steel strap
  • under trafficked areas, a reinforced concrete ring with cast-iron cover that does not bear on the tank (at least 50 mm clearance)
  • the neck can be shortened to suit the ground level or raised by up to 50 cm with the S038 (250 mm) or S039 (telescopic, 500 mm) extension

Rainwater, groundwater and swimming-pool water must not be fed into the tank. Installation, electrical connection and commissioning must be carried out by a qualified person.

Technical data

CodeDBL1300VS
ManufacturerIVAR
TypeIVAR.FEKAFOS KOMPLET
Tank volume1300 l
Tank height2000 mm
Tank outer diameter1020 mm
Inspection neck inner diameter625 mm
Tank materialpolyethylene (rotationally moulded)
Pumps2 × FEKA VS 1200 T-NA
Pump power supply3 × 400 V
ControlNG PANEL control unit
Inletconnector for PVC pipe DN 160
Pump impellervortex, solids up to 50 mm

Frequently asked questions

How are the two pumps of the FEKAFOS 1300 DOUBLE controlled?
The FEKA VS 1200 T-NA pumps have no float of their own – they are switched on by the NG PANEL according to level switches or probes. When the maximum level is exceeded, the panel activates a buzzer and the alarm outputs.

Can rainwater be fed into the tank?
No. Only waste water from the building may enter the tank – rainwater, groundwater and water from pools or aquariums must not be fed into it.

What if the tank sits too low below ground level after backfilling?
The neck can be raised by up to 50 cm with the S038 extension (250 mm) or the telescopic S039 extension (500 mm). Before fitting the extension, a rubber seal is placed on the neck of the inspection opening.

How is the tank installed where the groundwater level is high?
A C12/15 concrete base at least 15 cm thick is cast under the tank and the tank is anchored against buoyancy, for example with a stainless-steel strap fixed with M10 or M12 anchors.

Additional parameters

Category: DAB.FEKAFOS 280 DOUBLE - automatic pumping stations
Warranty: 2 years
Code: DBL1300VS
Manufacturer: IVAR
Type: IVAR.FEKAFOS KOMPLET
Tank volume: 1300 l
Tank height: 2000 mm
Tank outer diameter: 1020 mm
Inspection neck inner diameter: 625 mm
Tank material: polyethylene (rotationally moulded)
Pumps: 2 × FEKA VS 1200 T-NA
Pump power supply: 3 × 400 V
Control: NG PANEL control unit
Inlet: connector for PVC pipe DN 160
Pump impeller: vortex, solids up to 50 mm

Product rating

Be the first who will post an article to this item!

Do not fill out this field

How would you rate this product? Choose 1 to 5 stars, where 1 is the worst and 5 is the best rating.

Discussion

Be the first who will post an article to this item!

Do not fill out this field

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.