Male adapter PRESS-PPSU IVAR.PZ PPSU 20 x 3/4" M for ALPEX pipe
Code: 82820763Product detailed description
The IVAR.PZ PPSU 20 x 3/4" M adapter (code 82820763) has a press end for 20x2 pipes on one side and a 3/4" male thread on the other. It is used to connect ALPEX, TURATEC or PEX pipe to fittings with a female thread, for example ball valves or angle valves.
Features
- PPSU body, AISI 304 stainless steel press sleeve, EPDM O-ring, polycarbonate positioning ring
- max. operating pressure PN 10, temperature range +3 to +95 °C
- hygiene certificate for drinking water
- overall length 57 mm, weight 22 g
- radial pressing with jaws of profile B or F (according to the manual also TH)
Installation
When tightening the threaded fitting, hold the adapter body against rotation, otherwise the pipe may twist in the press joint. For sealing the thread, the IVAR manual recommends PTFE cord or tape; with hemp and approved paste, keep the thread crests visible and avoid excessive tightening torque. An unpressed joint leaks during the pressure test between 1 and 6.5 bar, so it is detected before the pipework is covered.
Technical data
| Code | 82820763 |
| Manufacturer | IVAR |
| Type | IVAR.PZ PPSU |
| Product type | press adapter with male thread |
| Size | 20 x 3/4" M |
| Press side | Ø 20 mm (ALPEX, TURATEC, PEX 20x2) |
| Thread | male 3/4" |
| Overall length L1 | 57 mm |
| Weight | 22 g |
| Max. operating pressure | PN 10 |
| Temperature range | +3 to +95 °C |
| Press jaws | B, F (also TH) |
| Material | PPSU, AISI 304 sleeve, EPDM O-ring, PC ring |
Frequently asked questions
What is the 20 x 3/4" M adapter used for?
It connects ALPEX, TURATEC or PEX pipe with a 20 mm diameter to a fitting with a 3/4" female thread, for example a ball valve or an angle valve.
What should the thread be sealed with?
The IVAR manual recommends PTFE cord or PTFE tape. With hemp and approved paste, the thread crests must remain visible – too much hemp or excessive torque can damage the fitting.
What should I watch out for when tightening the fitting?
Hold the adapter body against rotation while tightening the threaded fitting, otherwise the pipe may twist in the press joint.
Which jaws are used to press the adapter?
Radially, with B or F profile jaws for the 20 mm diameter; the manual also allows the TH profile. Calibrate and deburr the pipe before inserting it and check its position in the windows of the positioning ring.
Additional parameters
| Category: | straight press adapters - male thread |
|---|---|
| Warranty: | 2 years |
| Weight: | 0.022 kg |
| Fitting type: | adapter / transition |
| Pipe diameter: | 20 mm |
| Material: | stainless steel |
| Connection type: | press fitting |
| Code: | 82820763 |
| Manufacturer: | IVAR |
| Type: | IVAR.PZ PPSU |
| Product type: | press adapter with male thread |
| Size: | 20 x 3/4" M |
| Press side: | Ø 20 mm (ALPEX, TURATEC, PEX 20x2) |
| Thread: | male 3/4" |
| Overall length L1: | 57 mm |
| Weight: | 22 g |
| Max. operating pressure: | PN 10 |
| Temperature range: | +3 to +95 °C |
| Press jaws: | B, F (also TH) |
| Material: | PPSU, AISI 304 sleeve, EPDM O-ring, PC ring |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.