IVAR.EUROTANK VS3 2000 domestic hot water cylinder – 1990 l, 3 flanges for heating inserts
Code: 1J11B05Product detailed description
Hot water cylinder for several heat sources
The IVAR.EUROTANK VS3 2000 cylinder, with a total capacity of 1990 l, heats and stores hot water intended for human consumption. It is a floor-standing vessel made of sheet steel, designed for closed heating systems in which heat is supplied by a boiler, heat pump, fireplace insert, solar system or a combination of these.
The VS3 type is designed for systems with several heat sources. Instead of a fixed heat exchanger it has three integrated Ø 290/220 mm flanges for heating inserts. The manufacturer gives a recommended diagram in which the cylinder is heated by a gas boiler, a solar system and a fireplace insert. The 6/4" connection for an electric immersion heater is for emergency heating only.
Design and connections
- SMALVER internal lining based on synthetic resin, max. operating temperature 70 °C
- max. operating pressure 6 bar
- magnesium protective anode 5/4" and 1/2" connection for an electronic anode
- removable soft VLIES polyester-fibre insulation, 100 mm thick, reaction to fire class B-s2,d0, energy class C
- cold water inlet 2", hot water outlet 2", drain 5/4"
- 1/2" connections for temperature sensor and probe, 6/4" connection for electric heater or recirculation
Installation and maintenance
The cylinder is installed in a closed, ventilated room where the temperature never drops below +5 °C. For this capacity, a prepared horizontal base with sufficient load-bearing capacity and space for handling is required. When raising it upright, allow for the tilt height of 2520 mm and leave space above the top connections for replacing the anode. The insulation is fitted onto the vessel only at the installation site.
The cold water supply must include a ball valve, a check valve with test valve, a safety valve with an opening pressure below 6 bar and a pressure gauge. The manufacturer makes the warranty conditional on fitting a pressure-reducing valve and an expansion vessel – for this capacity it recommends a vessel of 100 to 200 l. The hardness of the supply water must not exceed 2 mmol/l (11.2 °dH).
Installation and commissioning may only be carried out by a qualified company, which completes the commissioning report and sends it to the supplier within 30 days. Once a year the cylinder is desludged and the condition of the anode is checked.
Technical data
| Code | 1J11B05 |
| Manufacturer | IVAR |
| Type | IVAR.EUROTANK VS3 2000 |
| Total capacity | 1990 l |
| Internal lining | SMALVER |
| Flange for heating insert | 3 × Ø 290/220 mm |
| Max. operating pressure | 6 bar |
| Max. operating temperature | 70 °C |
| Thermal insulation | VLIES 100 mm, removable |
| Energy class | C |
| Height with insulation | 2470 mm |
| Diameter with insulation | 1300 mm |
| Tilt height | 2520 mm |
| Empty weight | 351 kg |
| Cold water inlet / hot water outlet | 2" / 2" |
Frequently asked questions
What are the three flanges of the IVAR.EUROTANK VS3 2000 cylinder for?
Each Ø 290/220 mm flange can take one heating insert, so several heat sources can heat the cylinder at the same time. The manufacturer gives a connection with a gas boiler, solar system and fireplace insert.
Which expansion vessel suits a 1990 l cylinder?
The manufacturer recommends a potable water expansion vessel of 100 to 200 l, for example from the IVAR.AQUACOLD range. The exact size is determined by the designer, also taking into account the water in the pipework and recirculation.
What is the highest temperature the water in the cylinder may be heated to?
With the SMALVER internal lining, the maximum operating temperature is 70 °C and the maximum pressure 6 bar. The temperature must be limited on the heat source side.
What maintenance does the cylinder need?
Every year deposits are removed from the vessel and the magnesium anode is inspected; with aggressive water the anode is checked every six months. If its diameter falls below 22 mm, it must be replaced.
Additional parameters
| Category: | with multiple flanges option |
|---|---|
| Warranty: | 2 years |
| Weight: | 351 kg |
| Code: | 1J11B05 |
| Manufacturer: | IVAR |
| Type: | IVAR.EUROTANK VS3 2000 |
| Total capacity: | 1990 l |
| Internal lining: | SMALVER |
| Flange for heating insert: | 3 × Ø 290/220 mm |
| Max. operating pressure: | 6 bar |
| Max. operating temperature: | 70 °C |
| Thermal insulation: | VLIES 100 mm, removable |
| Energy class: | C |
| Height with insulation: | 2470 mm |
| Diameter with insulation: | 1300 mm |
| Tilt height: | 2520 mm |
| Empty weight: | 351 kg |
| Cold water inlet / hot water outlet: | 2" / 2" |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.
