Mayline SB IVAR.SB cleaning fluid for underfloor heating – 1% dosage, 5 l – SALE
Code: IVA5/MYSBRelated products
Product detailed description
What it is for
Algae, sludge and biological deposits in underfloor heating, radiant panels or other low-temperature circuits impair heat transfer. Mayline SB from the Italian manufacturer Maychem is a fluid based on organic compounds that loosens these deposits from the circuits and limits their further formation. It is intended exclusively for closed heating systems and must not be used in drinking water installations.
Properties
- suitable for iron, steel, copper, aluminium and their alloys, PEX pipes and multilayer pipes
- 1% dosage – 1 litre per 100 litres of heating water; higher or lower concentrations must not be used
- 5 l pack, yellow, odourless liquid
Cleaning procedure
First drain the sludge from the system and refill the circuit with clean mains water; all control valves must be fully open. Then add the product at a ratio of 1% and let it circulate – about 4 hours with the boiler circulation pump or about 5 hours with an external flushing pump, making sure the solution flows through each circuit for at least 2 hours. For large or heavily contaminated systems, cleaning is extended to up to 24 hours. The temperature must not exceed 40 °C during cleaning.
Afterwards, drain the solution and flush each circuit with mains water for 45–60 minutes. To protect the system after cleaning, the manufacturer recommends the Mayline SBA protective fluid (IVA1/MYSBA, IVA5/MYSBA).
Safety: the product causes serious eye damage. Wear gloves and safety goggles, keep out of the reach of children and protect from frost. Do not mix with other chemical additives. The same product is also available in a 1 l pack (IVA1/MYSB).
Technical data
| Code | IVA5/MYSB |
| Manufacturer | Maychem |
| Type | IVAR.SB |
| Trade name | Mayline SB |
| Pack size | 5 l |
| Application | underfloor and low-temperature heating, closed systems |
| Dosage | 1% (1 l per 100 l of water) |
| Cleaning time | 4 h with boiler circulation pump, 5 h with external pump |
| Max. temperature during cleaning | 40 °C |
| pH | 4.5–7 |
| Colour | yellow |
| Density | 1.04 g/cm³ |
| Protection after cleaning | Mayline SBA |
Frequently asked questions
Is Mayline SB suitable for underfloor heating with plastic pipes?
Yes. The product can be used with PEX pipes, multilayer pipes and metals such as steel, copper or aluminium and their alloys.
How much product do I need?
The dosage is 1% of the heating water volume, i.e. 1 litre per 100 litres. The 5 l pack is enough for a system containing 500 l of water.
Can the product be used in drinking water pipes?
No, Mayline SB is intended exclusively for closed heating systems.
What should be done after cleaning?
Drain the solution, flush each circuit with mains water for 45 to 60 minutes and then fill the system with a protective fluid such as Mayline SBA.
Additional parameters
| Category: | Chemicals |
|---|---|
| Warranty: | 24 |
| Availability: | In stock or at supplier |
| Code: | IVA5/MYSB |
| Manufacturer: | Maychem |
| Type: | IVAR.SB |
| Trade name: | Mayline SB |
| Pack size: | 5 l |
| Application: | underfloor and low-temperature heating, closed systems |
| Dosage: | 1% (1 l per 100 l of water) |
| Cleaning time: | 4 h with boiler circulation pump, 5 h with external pump |
| Max. temperature during cleaning: | 40 °C |
| pH: | 4.5–7 |
| Colour: | yellow |
| Density: | 1.04 g/cm³ |
| Protection after cleaning: | Mayline SBA |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.