Column filter IVAR.DEFEMN 200-5 for iron and manganese removal – 6/4", control with 5 buttons
Code: IVA.120.DF5Product detailed description
IVAR.DEFEMN 200-5 (code IVA.120.DF5) is a column filter for the removal of iron and manganese from drinking and utility water. The delivery includes a programmable fully electronic control unit WSCI with five buttons, which controls regeneration according to time or the volume passed. For proper operation, the filter is supplemented with a proportional dosing pump, which doses sodium hypochlorite at a concentration corresponding to the parameters of drinking water.
Dimensions and Performance
- dimensions 416 × 416 × 1858 mm (w × d × h), at least 200 mm of working space above the filter
- inlet/outlet connection 6/4", waste connection 1"
- estimated operating flow 12.0 m³/h – actual flow depends on water contamination and the design of the solution
Operating Conditions
- max. operating pressure 6 bar, temperature of treated water 5–35 °C
- dry room with temperature 5–40 °C and flat floor; only on consoles if the weight is evenly distributed
- connection to a sewage system with sufficient capacity and to the 230 V power grid
- complies with the requirements for permanent contact with drinking water according to the Czech government decree No. 409/2005 Coll.
Installation and Start-up
The system includes closing and sampling valves, pressure gauges, bypass, waste (e.g., transparent garden hose), dosing pump, impulse water meter, and a tank for the stock solution; a granular activated carbon filter is recommended at the outlet. Do not confuse the supply and discharge – the direction of flow is indicated by arrows on the inlet pipes of the head. After installation, the customer rinses the filter in the BACKWASH mode at a pressure of at least 3 bar until clean water flows from the waste; only then will the technician put it into operation and set the dosing, approximately 3 l of oxidizing agent is needed for start-up. Installation can be done by a local company, but commissioning must be carried out by an authorized company, otherwise the right to warranty repairs is lost.
Technical Parameters
| Code | IVA.120.DF5 |
| Manufacturer | IVAR |
| Type | IVAR.DEFEMN 200-5 |
| Type | column filter for the removal of iron and manganese |
| Dimensions (w × d × h) | 416 × 416 × 1858 mm |
| Inlet/Outlet Connection | 6/4" |
| Estimated Operating Flow | 12.0 m³/h |
| Waste Connection | 1" |
| Control Unit | WSCI with 5 buttons (time/volume) |
| Max. Operating Pressure | 6 bar |
| Temperature of Treated Water | 5–35 °C |
| Environmental Temperature | 5–40 °C |
| Power Supply | 230 V |
| Required Additional Equipment | proportional dosing pump |
Frequently Asked Questions
Why does the filter need a dosing pump?
For proper operation, it is necessary to install a proportional dosing pump, which doses sodium hypochlorite at a concentration corresponding to the parameters of drinking water. The dosing is set by the technician during commissioning.
How does the first rinse take place?
After installation, the customer rinses the filter in the BACKWASH mode at a pressure of at least 3 bar until clean water flows from the waste, which can take several hours. Then, an appointment for commissioning is arranged with the technical department of IVAR.
What must the water treatment system connection include?
Closing and sampling valves, pressure gauges, bypass, connection to the waste, dosing pump, impulse water meter, and a tank for the stock solution. A filter with granular activated carbon is recommended at the outlet.
What flow can the IVAR.DEFEMN 200-5 filter handle?
The estimated operating flow is 12.0 m³/h at a 6/4" connection. The actual flow depends on the overall water contamination and is determined by the technical solution design.
Additional parameters
| Category: | column filters |
|---|---|
| Warranty: | 2 years |
| Availability: | In stock or at supplier |
| Code: | IVA.120.DF5 |
| Manufacturer: | IVAR |
| Type: | IVAR.DEFEMN 200-5 |
| Product: | column filter for iron and manganese removal |
| Dimensions (W × D × H): | 416 × 416 × 1858 mm |
| Inlet/outlet connection: | 6/4" |
| Operating flow (indicative): | 12.0 m³/h |
| Drain connection: | 1" |
| Control unit: | WSCI with 5 buttons (time/volume) |
| Max. operating pressure: | 6 bar |
| Treated water temperature: | 5–35 °C |
| Ambient temperature: | 5–40 °C |
| Power supply: | 230 V |
| Required addition: | proportional dosing pump |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.