RESICLEAN cleaning agent (GEL.RESICLEAN) for the resin of IVAR.DEVAP water softeners – 1 l – SALE
Code: 109.081.65Related products
Product detailed description
The cation exchange resin in a water softener consists of tiny beads and also acts as a filter medium – it captures particles from the incoming water. If well or borehole water contains iron, manganese or other elements that oxidise and precipitate into sludge, they settle on the surface of the beads, reduce the exchange capacity and accelerate ageing of the resin. Normal regeneration does not remove these deposits completely, which is why RESICLEAN is drawn into the softener from time to time.
Dosage
Use 15 ml of the agent per 1 litre of resin. For IVAR.DEVAP-KAB softeners this means 75 ml (005), 150 ml (010), 225 ml (015), 300 ml (020), 375 ml (025) and 450 ml (030); for IVAR.DEVAP 030 to 500 from 450 ml to 7500 ml. Clean at least once a year, more often if the raw water quality is poorer.
Procedure in brief
- check that there is enough salt in the brine tank for a standard regeneration
- start a manual regeneration with the REGEN button, move from the BACKWASH phase to the BRINE phase and disconnect the power
- immerse the brine tube in the container with the measured agent, let it be drawn in completely and time it
- let the agent act – 1 second of suction corresponds to 1 minute of contact time
- reconnect the tube, restore power, step through the RINSE and FILL phases and finally let one more complete regeneration run
The agent is also made in 250 ml (109.081.60) and 5 l (109.081.70) packs.
Technical data
| Code | 109.081.65 |
| Brand | IVAR |
| Type | GEL.RESICLEAN |
| Pack size | 1 l |
| Purpose | cleaning the cation exchange resin of water softeners |
| Suitable for | IVAR.DEVAP, IVAR.DEVAP-KAB |
| Dosage | 15 ml per 1 l of resin |
| Recommended frequency | at least once a year |
| Contact time | 1 s of suction = 1 min of contact |
Frequently asked questions
How much agent do I need for one cleaning?
15 ml for every litre of resin in the softener. For example, IVAR.DEVAP-KAB 010 needs 150 ml and DEVAP-KAB 030 needs 450 ml.
How often should the softener be cleaned?
At least once a year is recommended. More often if the water contains iron, manganese or other impurities.
How long should the agent act in the softener?
Time how long it takes for the agent to be drawn in – each second of suction corresponds to one minute of contact. Then the regeneration is completed and one more full regeneration is started.
Does RESICLEAN replace regeneration salt?
No, the brine tank must contain enough salt for a standard regeneration. RESICLEAN is used for occasional thorough cleaning of the resin.
Additional parameters
| Category: | softening filters |
|---|---|
| Warranty: | 24 |
| Availability: | In stock or at supplier |
| Code: | 109.081.65 |
| Brand: | IVAR |
| Type: | GEL.RESICLEAN |
| Pack size: | 1 l |
| Purpose: | cleaning the cation exchange resin of water softeners |
| Suitable for: | IVAR.DEVAP, IVAR.DEVAP-KAB |
| Dosage: | 15 ml per 1 l of resin |
| Recommended frequency: | at least once a year |
| Contact time: | 1 s of suction = 1 min of contact |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.