Quartz glass sleeve for IVA.HA365 UV steriliser – IVAR spare part
Code: IVA.HA540Related products
Product detailed description
The IVA.HA540 tube is an original spare part for the IVA.HA365 UV steriliser from the IVAR.UV LIGHT KIT MAX range (model FC-20, 6/4" connection, max. flow 4536 l/h, power 65 W). This quartz glass sleeve houses the low-pressure UV lamp inside the stainless steel chamber; the lamp emits 254 nm radiation to disinfect drinking or pool water.
Recommended maintenance
- clean the sleeve every 3 to 6 months depending on water quality, using alcohol or a special detergent
- replace the sleeve every 24 months
- replace the O-ring after 9 to 12 months and the UV lamp after approximately 10,000 operating hours
Replacing the sleeve
After unscrewing the nut and disconnecting the connector, carefully slide the UV lamp out of the sleeve. Then remove the O-rings and pull the sleeve out of the chamber – it helps to hold it from behind with a finger so that it does not slip to the bottom as it comes out. Reassemble in reverse order, making sure the O-ring sits correctly on the sleeve. Quartz glass is very fragile, so do not overtighten the nut. UV radiation is harmful to the eyes and skin.
For the same IVA.HA365 unit, the replacement UV lamp IVA.HA510 and the silicone O-ring IVA.HA552A are also available.
Technical data
| Code | IVA.HA540 |
| Brand | IVAR |
| Type | IVAR.PRISLUSENSTVI |
| Part type | UV lamp sleeve (tube) |
| Material | quartz glass |
| Designed for | UV steriliser IVA.HA365 (model FC-20) |
| UV steriliser connection | 6/4" |
| Cleaning interval | 3–6 months |
| Recommended replacement | every 24 months |
| Related parts | UV lamp IVA.HA510, O-ring IVA.HA552A |
Frequently asked questions
Which UV steriliser does the IVA.HA540 sleeve fit?
It is designed for the IVA.HA365 UV steriliser from the IVAR.UV LIGHT KIT MAX range, model FC-20 with 6/4" connection.
How often should the sleeve be cleaned and replaced?
It should be cleaned every 3 to 6 months depending on water quality, using alcohol or a special detergent. The manufacturer recommends replacing it every 24 months.
Are the UV lamp or O-ring included?
No, the item is the glass sleeve only. The UV lamp IVA.HA510 and the O-ring IVA.HA552A are separate spare parts.
Additional parameters
| Category: | UV lamps and reverse osmosis systems |
|---|---|
| Warranty: | 24 |
| Availability: | In stock or at supplier |
| Code: | IVA.HA540 |
| Brand: | IVAR |
| Type: | IVAR.PRISLUSENSTVI |
| Part type: | UV lamp sleeve (tube) |
| Material: | quartz glass |
| Designed for: | UV steriliser IVA.HA365 (model FC-20) |
| UV steriliser connection: | 6/4" |
| Cleaning interval: | 3–6 months |
| Recommended replacement: | every 24 months |
| Related parts: | UV lamp IVA.HA510, O-ring IVA.HA552A |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.