Water treatment unit with reverse osmosis IVAR.CROSS 90 – five-stage, with mineralization, 90 l/h, 433 × 136 × 452 mm – SPECIAL OFFER – SALE
Code: ESMO3600MPECOProduct detailed description
Five stages in three cartridges
IVAR.CROSS 90 BALANCE purifies water sequentially in three replaceable cartridges. The comprehensive pre-filter CF made of composite polypropylene and an activated carbon block will capture sand, silt and rust and reduce chlorine and organic content. Next comes a reverse osmosis membrane 600 GPD, which removes up to 99.8% of impurities including bacteria, viruses and PFAS. Finally, the water passes through a mineralizing post-filter MCB with activated carbon – it enhances taste and smell and enriches the water with minerals (total content 40–70 mg/l).
Without a tank, with status display
The purification unit is direct-flow: with a flow rate of 1.5 l/min (90 l/h), it fills a 200 ml glass in approximately 8 seconds. The booster pump is powered from 230 V. The device and the intelligent outlet tap indicate water preparation, faults and the need to replace individual stages; water leak protection and an installation kit are included.
Maintenance and installation
- pre-filter CF (ESCPVDFRO): once every 12 months or after 4000 l
- RO membrane (ESCSVRO600DFRO): once every 24 months or after 8000 l
- mineralizing post-filter MCB (ESPDCBDFRO): once every 12 months or after 4000 l
Cartridge replacement is dry and takes up to 10 minutes. The input water pressure should be 2–5 bar and a pressure regulator before the unit is mandatory; the device is intended for cold water only. Water recovery is 60%, and materials are certified according to NSF/ANSI 58.
Technical specifications
| Code | ESMO3600MPECO |
| Brand | IVAR |
| Type | IVAR.CROSS90 (CROSS 90 BALANCE) |
| System | five-stage reverse osmosis with mineralization |
| Direct flow | 1.5 l/min (90 l/h) |
| Membrane | RO 600 GPD |
| Recovery (water saving) | 60 % |
| Input water pressure | 2–5 bar |
| Power supply | 230 V, 50–60 Hz |
| Dimensions (h × w × d) | 433 × 136 × 452 mm |
| Mineral content in purified water | 40–70 mg/l |
| Material certification | NSF/ANSI 58 |
| Replacement cartridges | ESCPVDFRO, ESCSVRO600DFRO, ESPDCBDFRO |
| Cartridge replacement | dry, up to 10 minutes |
Frequently asked questions
How often are the cartridges replaced in the IVAR.CROSS 90?
The comprehensive pre-filter CF and the mineralizing post-filter MCB once every 12 months or after 4000 l, the RO membrane once every 24 months or after 8000 l. The need for replacement will be indicated by the indicator on the device and on the outlet tap.
Why does the water taste different after replacing the post-filter?
The new mineralizing and carbon material has maximum capacity at the beginning of its life, so the change in taste and smell is normal. These properties gradually stabilize during operation.
Can I connect the unit to hot water?
No, the home water purification unit with reverse osmosis is intended for cold water only. The supply must have a pressure of 2–5 bar and a pressure regulator must be installed before the unit.
Additional parameters
| Category: | UV lamps and reverse osmosis systems |
|---|---|
| Warranty: | 2 years |
| Availability: | In stock or at supplier |
| Code: | ESMO3600MPECO |
| Brand: | IVAR |
| Type: | IVAR.CROSS90 (CROSS 90 BALANCE) |
| System: | five-stage reverse osmosis with remineralisation |
| Direct flow: | 1.5 l/min (90 l/h) |
| Membrane: | RO 600 GPD |
| Recovery (water saving): | 60 % |
| Inlet water pressure: | 2–5 bar |
| Power supply: | 230 V, 50–60 Hz |
| Dimensions (H × W × D): | 433 × 136 × 452 mm |
| Mineral content of treated water: | 40–70 mg/l |
| Material certification: | NSF/ANSI 58 |
| Replacement cartridges: | ESCPVDFRO, ESCSVRO600DFRO, ESPDCBDFRO |
| Cartridge change: | dry, within 10 minutes |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.