Filter 9 3/4" IVAR.FP3.TRIPLEX – 1" F, with cartridges including granular activated carbon – SALE
Code: IVAA1131025GACProduct detailed description
The IVAR.FP3.TRIPLEX (code IVAA1131025GAC) is a three-piece 9 3/4" filter in which water passes through three filtration stages in turn. It traps mechanical impurities such as sand, swarf or fine corrosion particles and is also suitable for final fine filtration of rainwater. This version is supplied with cartridges including a granular activated carbon stage.
Cartridges supplied
- RL-A – 80 µm
- GAC40 – 40 µm, granular activated carbon
- FR-N – 20 µm, PP melt-blown
Technical data
- inlet/outlet connection 1" F, max. operating flow 3.6 m³/h
- pressure rating PN 10, water temperature +5 to +40 °C
- dimensions 396 × 365 × 145 mm, SAN body, PP head
Installation and maintenance
- installation should be carried out by a qualified installer; a pressure reducing valve is required if mains pressure exceeds 8 bar
- in systems without an expansion vessel, a buffer pressure vessel of at least 2 l must be fitted upstream
- we recommend a pressure gauge before and after the filter – at a pressure difference above 0.5 bar, clean or replace the cartridge
- observe the flow direction arrow, anchor the filter and protect it from frost and direct sunlight
When replacing, put the cartridge into the bowl first, then fit the bowl to the head and tighten the union nut by hand. The IVAAVAFP3 wrench is used to loosen the nuts. FR-N, F-A, RLA, AC-HT, GAC40 and CTO-E cartridges are suitable replacements. The IVAA1131025K variant is supplied with 250, 80 and 20 µm cartridges.
Technical data
| Code | IVAA1131025GAC |
| Manufacturer | IVAR |
| Type | IVAR.FP3.TRIPLEX |
| Product | three-piece mechanical impurity filter |
| Size | 9 3/4" |
| Connection | 1" F |
| Max. operating flow | 3.6 m³/h |
| Pressure rating | PN 10 |
| Water temperature | +5 to +40 °C |
| Dimensions | 396 × 365 × 145 mm |
| Material | SAN body, PP head |
| Cartridges supplied | RL-A 80 µm, GAC40 40 µm, FR-N 20 µm |
Frequently asked questions
Which cartridges does the filter contain?
The filter comes with three cartridges: RL-A with 80 µm porosity, GAC40 with granular activated carbon (40 µm) and FR-N made of PP melt-blown with 20 µm porosity.
When should the cartridges be cleaned or replaced?
A pressure gauge before and after the filter is recommended. When the pressure difference exceeds 0.5 bar, the cartridge must be cleaned or replaced.
What should be considered during installation?
If mains pressure exceeds 8 bar, fit a pressure reducing valve upstream. If the system has no expansion vessel, install a buffer pressure vessel of at least 2 l upstream of the filter.
What other cartridges can be used?
The filter takes FR-N, F-A, RLA, AC-HT, GAC40 and CTO-E cartridges. The IVAAVAFP3 mounting wrench is used to loosen the nuts.
Additional parameters
| Category: | filters for drinking water |
|---|---|
| Warranty: | 2 years |
| Type: | water filter |
| Thread size: | 1" |
| Filter / cartridge size: | 10" |
| Code: | IVAA1131025GAC |
| Manufacturer: | IVAR |
| Type: | IVAR.FP3.TRIPLEX |
| Product: | three-piece mechanical impurity filter |
| Size: | 9 3/4" |
| Connection: | 1" F |
| Max. operating flow: | 3.6 m³/h |
| Pressure rating: | PN 10 |
| Water temperature: | +5 to +40 °C |
| Dimensions: | 396 × 365 × 145 mm |
| Material: | SAN body, PP head |
| Cartridges supplied: | RL-A 80 µm, GAC40 40 µm, FR-N 20 µm |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.