Mechanical impurity filter IVAR.BIG BLUE 4.5 × 10" – 1" F, without cartridge – SALE
Code: ESFPV4510ECOProduct detailed description
The IVAR.BIG BLUE (code ESFPV4510ECO) is a two-piece polypropylene filter fitted on the incoming cold-water pipe. It traps mechanical impurities – rust particles, sand, silt and sediment – and removes turbidity. It is suitable for mains water, well water and rainwater.
Technical data
- filter cartridge size 4.5 × 10"
- 1" female thread connection
- max. flow 50 l/min
- operating pressure 2 to 6 bar (PN 6), water temperature +5 to +40 °C
Suitable filter cartridges
- ESCPV45105ECO – 5 µm, 100% polypropylene (melt-blown)
- ESCHVCB4510ECO – 10 µm, pressed activated carbon block
- ESCHV4510ECO – 40 µm, granular activated carbon filling
Contents and installation
Supplied with the filter body, a wall bracket with 4 screws, a mounting wrench for cartridge changes and instructions – the filter cartridge is not included. Have a qualified installer fit the filter, seal the threads with PTFE tape; the manufacturer recommends a pressure regulator upstream. Replace the cartridge depending on water quality, usually every 2 to 6 months; the filter housing has a service life of 5 years. The filter is not intended for hot water or microbiologically unsafe water.
Technical data
| Code | ESFPV4510ECO |
| Manufacturer | IVAR |
| Type | IVAR.BIG BLUE |
| Product | two-piece mechanical impurity filter |
| Cartridge size | 4.5 × 10" |
| Connection | 1" F |
| Max. flow | 50 l/min |
| Operating pressure | 2–6 bar (PN 6) |
| Water temperature | +5 to +40 °C |
| Material | polypropylene (PP) |
| Filter cartridge | not included |
| Housing service life | 5 years |
Frequently asked questions
Is the filter cartridge included?
No. The pack contains the filter body, a wall bracket with 4 screws, a mounting wrench and instructions. Choose the 4.5 × 10" cartridge according to water quality.
Which cartridges fit the filter?
The 4.5 × 10" filter takes cartridges ESCPV45105ECO (5 µm, PP melt-blown), ESCHVCB4510ECO (10 µm, activated carbon block) and ESCHV4510ECO (40 µm, granular activated carbon).
How often should the cartridge be replaced?
Depending on water quality, usually every 2 to 6 months, or according to the water meter or when its capacity drops. The manufacturer recommends original IVAR.BIG BLUE cartridges only.
Can I use the filter for hot water?
No, the filter is designed for cold water at +5 to +40 °C. It is also not suitable for microbiologically unsafe water without prior disinfection.
Additional parameters
| Category: | filters for drinking water |
|---|---|
| Warranty: | 2 years |
| Type: | water filter |
| Thread size: | 1" |
| Filter / cartridge size: | 10" |
| Code: | ESFPV4510ECO |
| Manufacturer: | IVAR |
| Type: | IVAR.BIG BLUE |
| Product: | two-piece mechanical impurity filter |
| Cartridge size: | 4.5 × 10" |
| Connection: | 1" F |
| Max. flow: | 50 l/min |
| Operating pressure: | 2–6 bar (PN 6) |
| Water temperature: | +5 to +40 °C |
| Material: | polypropylene (PP) |
| Filter cartridge: | not included |
| Housing service life: | 5 years |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.