UV sterilisation lamp IVAR.UV LIGHT KIT MAX IVA.HA380 – 2", 10 200 l/h, 120 W
Code: IVA.HA380Product detailed description
How the UV steriliser works
Inside the polished AISI 304 stainless steel chamber, the UV lamp sits in a quartz glass sleeve. The low-pressure lamp emits monochromatic UVC radiation at a wavelength of 254 nm, which damages the RNA and DNA of microorganisms so that they cannot multiply. The irradiation dose exceeds 40 mJ/cm².
Model FC-45
- max. flow 10 200 l/h
- connection 2" BSP M (male thread)
- power input 120 W, 230 V / 50 Hz
- chamber diameter 160 mm, overall length 1235 mm, connection centre distance 983 mm
- max. pressure 7 bar, operating temperature +5 to +40 °C
- control box with electronics, hour meter, switch and LED fault indicator, protection rating IP43
Model FC-45 allows a shut-off solenoid valve to be connected.
Maintenance and installation
- clean the quartz sleeve every 3–6 months with alcohol or a special cleaner and replace it after 24 months
- replace the O-ring every 9–12 months
- replace the UV lamp after 10 000 operating hours (roughly 9–12 months)
Install the steriliser in an easily accessible, frost-free place (min. +5 °C). Installation and electrical connection may only be carried out by a qualified person. UV radiation is harmful to skin and eyes, and the quartz glass is fragile – handle it with care.
Technical data
| Code | IVA.HA380 |
| Brand | IVAR |
| Type | IVAR.UV LIGHT KIT MAX |
| Model | FC-45 |
| Max. flow | 10 200 l/h |
| Connection | 2" BSP M (2") |
| Power input | 120 W |
| Power supply | 230 V / 50 Hz |
| Wavelength | 254 nm (UVC) |
| Irradiation dose | > 40 mJ/cm² |
| Max. pressure | 7 bar |
| Chamber material | AISI 304 |
| Dimensions | Ø 160 mm, length 1235 mm |
| Lamp service life | approx. 10 000 h |
| Spare parts | lamp HA516, quartz sleeve HA542, O-ring HA552 |
Frequently asked questions
What flow can the IVA.HA380 UV lamp handle?
Model FC-45 handles a maximum of 10 200 l/h with a 2" connection and is the most powerful model in the IVAR.UV LIGHT KIT MAX range.
How often does the UV lamp need replacing?
After about 10 000 operating hours, which is roughly 9–12 months. After that the effectiveness of the germicidal radiation drops sharply, even though the lamp still lights up.
How should the quartz sleeve be looked after?
Clean it every 3–6 months, depending on water quality, with alcohol or a special cleaner and replace it after 24 months. The O-ring is replaced every 9–12 months.
Additional parameters
| Category: | UV lamps and reverse osmosis systems |
|---|---|
| Warranty: | 2 years |
| Type: | UV lamp |
| Code: | IVA.HA380 |
| Brand: | IVAR |
| Type: | IVAR.UV LIGHT KIT MAX |
| Model: | FC-45 |
| Max. flow: | 10 200 l/h |
| Connection: | 2" BSP M (2") |
| Power input: | 120 W |
| Power supply: | 230 V / 50 Hz |
| Wavelength: | 254 nm (UVC) |
| Irradiation dose: | > 40 mJ/cm² |
| Max. pressure: | 7 bar |
| Chamber material: | AISI 304 |
| Dimensions: | Ø 160 mm, length 1235 mm |
| Lamp service life: | approx. 10 000 h |
| Spare parts: | lamp HA516, quartz sleeve HA542, O-ring HA552 |
Product rating
Be the first who will post an article to this item!
Discussion
Be the first who will post an article to this item!
IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.
Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.
Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.
“Made in Italy” adds value
IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.
The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.
Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.
The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.
As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.